Trim Tab Meltdown

The Main Sand Box for bertram31.com

Moderators: CaptPatrick, mike ohlstein, Bruce

Post Reply
User avatar
STeveZ
Senior Member
Posts: 239
Joined: Jul 4th, '06, 08:16
Location: Chesapeake Bay, MD

Trim Tab Meltdown

Post by STeveZ »

At the end of last season my trim tabs ceased operation and I found fluid in the bilge. I was waiting to re-install my batteries before tinkering with them but decided yesterday to tear the pump out.

My observations (based on limited knowledge) are as follows:

The pumping/control mechanisms are housed under the upper red cover.
The fluid is contained in the white/opaque plastic reservoir below.
The two appear to be connected via a thin metal tube.

Image

Image

Image

My tube appears to have broken. Replacement of this tube and possibly some connecting hardware would not, on the face of it, seem like a big deal for an amateur.

I've found the Boat Leveler site along with a long list of parts. As always I'm tempted just to buy a new motor pump unit at $300 and dump the broken unit on ebay to defray the cost. Finally my question, anyone have any experience or knowledge of this repair?
User avatar
AndreF
Senior Member
Posts: 711
Joined: Jun 29th, '06, 09:53
Location: Baton Rouge, Louisiana
Contact:

Post by AndreF »

I just replaced hoses and rams for $100 each +/_. My pump was OK.
I'm not sure but indecision may or may not be my problem.

"People sleep peaceably in their beds at night only because rough men stand ready to do violence on their behalf." - George Orwell

1981 FBC BERG1883M81E
User avatar
CaptPatrick
Founder/Admin
Posts: 4161
Joined: Jun 7th, '06, 14:25
Location: 834 Scott Dr., LLANO, TX 78643 - 325.248.0809 bertram31@bertram31.com

Post by CaptPatrick »

Steve,

Replace the whole assembly. You ain't got nothing there but junk...

Br,

Patrick
User avatar
STeveZ
Senior Member
Posts: 239
Joined: Jul 4th, '06, 08:16
Location: Chesapeake Bay, MD

Post by STeveZ »

Actually it cleaned up remarkably well with Castrol GTX, CX and Blue cleaner.

Image

Image

Still, I was force to drill out the remnants of the broken fluid tube which might make the new tube leak, or may have messed up the pump beyond.
I may have fried something trying to run it off a battery in my garage too.
Better than 50% chance I'll end up w/ a whole new "red box".......$310....

BTW, the folks at Insta-Trim have been very helpful over the phone.
keysdisease
Posts: 30
Joined: Jan 14th, '07, 20:01
Location: Ft. Lauderdale, FL
Contact:

Boat leveler

Post by keysdisease »

Hi Steve,

I used to work for Bennett trim tabs and can help a little with how the system works.

If you ground the motor and put 12V directly to one of the wires going into the motor and the motor does not turn, it'd dead.

The Insta-Trim pump uses a reversing motor to put the tabs either up (motor forward) or down (motor reverse) The unit has a common ground and two positive wires going to the motor, the switch at the helm energizes one or the other.

At the same time the motor is turning one or both of the solenoids is energized to open and direct fluid either port, stbd or both.

Contrary to popular belief when running in reverse (to retract) the pump is not "pulling" the tabs up but there is a "return" spring in the actuator that does most of the work of "pushing the tabs up.

Bennett and Insta-Trim pumps are interchangable with minor modifications. You would need a pump bracket and to change the compression fittings for tube to hose nipples for hose to use a Bennett pump on a Insta-Trim system. You would also need the color cross reference for the wiring, both use a 4 wire harness.

Hope this is helpful, I always find it useful to know how and why things work on my boat.

Steve Moyer :-D
Soundown Ft. Lauderdale
Post Reply

Who is online

Users browsing this forum: Bing [Bot] and 64 guests